Included in box:
① — (2x) 3M VHB
② — (1x) Isopropyl Alcohol Wipe
③ — (1x) Visor Drilling Guide
④ — (1x) 18-8 Stainless Steel 4-40 Thread, 5/16" Long Screw
NOT INCLUDED (Necessary for permanent mount):
⑤ — (1x) 1/8” (3.175mm) Drill Bit
Purchase Link: https://amzn.to/4fRHRyz
⑥ — (1x) 82° Countersink Bit
Purchase link: https://amzn.to/3ZcAaN5
Mounting with Adhesive
STEP 1
Find the “true” center of your visor by using soft measuring tape. It’s typically helpful to either place a thin tape in the middle of your visor or painters tape with a middle mark with a pen or pencil.
STEP 2
Clean the area that you will be mounting the BOSS VISION // Race to with the included ② Isopropyl Alcohol Wipe
STEP 3
Peel back protective backing on the adhesive of your BOSS VISION // Race. It’s often easier to remove if you get a blade underneath the backing.
STEP 5
Place BOSS VISION // Race where you had determined as the true center. There is an arrow in the back of BOSS VISION // Race that can help you align.
Make sure that the flat ledge (highlighted in purple) is seated on your visor for proper fitment. Press and hold BOSS VISION // Race onto your visor for approximately 60 seconds for a stronger adhesion.
mounting with screw
(OPTIONAL)
STEP 2
Mock up where you will be mounting the BOSS VISION // Race. Do not remove the protective backing from the mount yet.
STEP 3
Line up the ③ Visor Drilling Guide and make sure that the arrow on the guide and the BOSS VISION // Race are aligned with the true center of your visor.
DISCLAIMER:
Boss Boss Racing is not liable for any damages made to your visor.
STEP 1
Same as adhesive mounting only; find the “true” center of your visor by using soft measuring tape. It’s typically helpful to either place a thin tape in the middle of your visor or painters tape with a middle mark with a pen or pencil.
STEP 4
Peel back the 3M VHB on the ③ Visor Drilling Guide.
STEP 5
Place the ③ Visor Drilling Guide on the center of the inside of your visor. Take your time and mock-up the BOSS VISION // Race mount to make sure that the arrows are aligned on the mount and the drilling guide.
STEP 6
IMPORTANT:
USE A NEW DRILL BIT TO PREVENT ANY WALKING OF THE BIT OR IMPROPER DRILLING.
With your ⑤ 1/8” (3.175mm) Drill Bit, drill through the guided hole on the ③ Visor Drilling Guide and through your visor. Make sure to drill slowly and make a conscious effort to be drilling straight and not at an angle.
STEP 7
With your ⑥ 82° Countersink Bit, SLOWLY AND CAREFULLY countersink the hole you’ve made in your visor. You will have to drill little by little and constantly set your ④ 18-8 Stainless Steel 4-40 Thread, 5/16" Long Screw in the hole until the head of the screw is completely flush with the visor and are able to run your finger across your visor without feeling the head of the screw sticking out.
STEP 8
Peel back protective backing on the adhesive of your BOSS VISION // Race and prep the surface of the front of the visor where you will be attaching the mount to with the included ② Isopropyl Alcohol Wipe.
It’s often easier to remove the protective backing if you get a blade underneath the backing.
STEP 9
Final step! With a No. 1 screwdriver (not included), screw the ④ 18-8 Stainless Steel 4-40 Thread, 5/16" Long Screw in to the BOSS VISION // Race mount through the countersunk hole you just made.
Be sure not to overtighten, as you may strip the threads.